Suggestions
NEW

DULCOTEST SurfaceGuard sensor for biofilm and scaling

Coating thickness measurement in the range of 0–200 µm
Measurement value availability: adjustable between 1 min and 2 h

DULCOTEST SurfaceGuard detects biofilms and inorganic deposits on process surfaces in real time. Its innovative heat transfer measurement principle detects even the thinnest layers in the micrometer range. This enables representative measurements as well as the targeted, timely, and efficient control of cleaning and dosing processes.

Product description

Reliable protection against biofilm and scaling through real-time monitoring

DULCOTEST SurfaceGuard is an innovative measurement system for real-time monitoring of deposits on process surfaces. The measurement system consists of a sensor and a transmitter that allows the sensor to be configured.

The innovative use of two sensors with differently configured surface temperatures enables a precise distinction between biofilms and inorganic deposits. This paves the way for targeted, automated, and needs-based measures such as the efficient dosing of biocides or antiscalants—for optimal process control and sustainable, low-chemical operation.

By emulating rheological and thermodynamic surface properties, DULCOTEST SurfaceGuard enables precise film thickness measurement of a wide variety of deposits across diverse industrial applications. This ensures representative monitoring of process surfaces—for maximum safety and efficiency.

Thanks to permanent factory calibration When a metering pump has been installed, the capacity in litres per hour has to be determined under ... more in the glossary, the system remains precise for a long time and requires minimal maintenance. This significantly extends maintenance intervals and noticeably reduces operating costs. Continuous measurement enables seamless monitoring of process efficiency—such as heat transfer in heat exchangers—allowing performance losses to be detected early and their effects minimized.

Your benefits

  • Reduces energy costs by ensuring the efficiency of industrial systems
  • Enhances process reliability through reliable real-time measurement of biofilms and scaling in the micrometer range
  • Enables targeted and effective measures because biofilm and inorganic deposits are clearly distinguished
  • Provides representative measured values by emulating the process surfaces to be monitored, enabling optimal control of water treatment processes
  • Identifies process changes early, before they negatively impact performance or hygiene
  • Reduces maintenance effort and downtime, as no time-consuming recalibration is required

Field of application

The following list of applications are general examples of generally suitable applications for this product. Please contact your local sales representative to talk about the applicable use of this product in your specific case / environment.

  • Power Generation: Monitoring Biofilms and Scaling in Open Cooling Circuits and Control of Countermeasures
  • Food & Beverage:
    • Cleaning-in-Place (CIP) Process: Monitoring the cleaning of product-carrying pipework and tanks. Control of corrective measures
    • Monitoring scaling in sugar production
  • Drinking Water Production: Monitoring of biofilms and scaling in reservoirs and distribution networks
  • Pulp & Paper: Monitoring of biofilms in production and control of measures
  • Mining: Monitoring scaling in pipework|tubing and control of countermeasures
  • Plastics processing: Monitoring biofilm formation on products
  • Steel mills: Monitoring scaling in pipework|tubing and control of countermeasures
  • Marine Applications: Monitoring scaling and control of countermeasures
  • Refineries: Monitoring of biofilms and scaling, and control of countermeasures

    Technical Details

    • Coating thickness measurement in the range of 0–200 µm
    • Measurement interval: adjustable from 1 min to 2 h
    • Biofilm measurement at a sensor temperature < 35°C
    • Measurement of inorganic deposits at a sensor temperature > 40°C
    • Emulation of the following process surface parameters:
      • Thickness of the surface material
      • Thermal conductivity of the surface material
      • Thermal conductivity of the coating
      • Process temperature
    • The SurfaceGuard measurement systems include one V4A installation kit per sensor for connecting the sensor to a 1 1/2" V4A T-fitting (female, provided by the customer). To connect the sensor to a 1 1/2" PVC T-fitting (female, provided by the customer), the optionally available installation kit for the SurfaceGuard SGS1 PVC sensor (1182765) can be used.

    Technical data for the DULCOTEST SurfaceGuard sensor

    Measured variable

    Coating thickness

    Measuring range

    0…200 μm

    Measuring accuracy

    ±5 μm

    pH-range

    1…13 (V4A design)
    2 … 13 (PVC design)

    Medium temperature

    0 … 120 °C (1.4571 design)
    0 … 60 °C (PVC-U design)

    Max. pressure

    3.0 bar, 6.0 bar with safety device

    minimum flow velocity

    0.4 m/s (non-laminar flow)

    Materials in Contact With the Medium

    Titanium, PEEK

    Supply voltage

    using the DULCOTEST SurfaceGuard Transmitter

    Heating capacity

    1 … 50 W, adjustable

    Electrical Connection

    5 m fixed cable

    Process integration

    Inline via R 1 1/2", 1.4571 adapter (male thread, R 1 1/2") to a 1 1/2-inch stainless steel T-fitting or weld-on straight union (T-fitting and straight union to be provided by the customer), horizontal. Optionally, the sensors can be connected inline via the G 1 1/2" PVC installation kit (1182765) to a G 1 1/2" PVC T-fitting (T-fitting and straight union to be provided by the customer).

    Enclosure rating

    IP 66

    Shaft diameter

    32 mm

    Shaft length

    300 mm

    Sensor area

    2.5 cm2

    Technical data for the DULCOTEST SurfaceGuard Transmitter

    Voltage supply

    EU-Version: 230 V AC ± 10%, 50 Hz, 2 A max.
    US-Version: 115 V AC ± 10%, 60 Hz, 3 A max.

    Inputs and outputs

    Inputs:
    2 x inputs for DULCOTEST SGS1 sensors
    2 x 4…20 mA (configurable via the web interface)
    Outputs:
    4 x 4…20 mA (configurable via the web interface)

    Communication interface

    LAN (Ethernet) on the Web Interface

    Enclosure rating

    IP 65

    Ambient temperature

    -10 ... +40 °C

    Relative Air Humidity

    5 … 95% (non-condensing)

    Degree of contamination

    Pollution Degree 3 (according to EN 61010-1)

    Elevation

    up to 2,000 m above sea level

    Dimensions H x W x D

    173 x 300 x 96 mm

    Order no.

    SurfaceGuard Kit: Measurement System with 1 Sensor (230 V) and 1.4571 Sensor Adapter

    1166246

    SurfaceGuard Kit: Measurement System with 2 Sensors, 230 V, with 1.4571 Sensor Adapters

    1166247

    SurfaceGuard Kit: Measurement System with 1 Sensor (115 V) and 1.4571 Sensor Adapter

    1182742

    SurfaceGuard Kit: Measurement System with 2 Sensors, 115 V, with 1.4571 Sensor Adapters

    1182743

    Accessories

    Order no.

    SurfaceGuard Sensor SGS1

    1165058

    Installation Kit for SurfaceGuard Sensor SGS1 V4A

    1166237

    Installation Kit for SurfaceGuard Sensor SGS1 PVC

    1182765

    Downloads for DULCOTEST SurfaceGuard sensor for biofilm and scaling

    More in the Download Centre

    0 Results
    Filter by document type
    Application Example / Reference (0)
    Brochure / Flyer (0)
    Catalogue (0)
    Certificate / Declaration (0)
    Data Sheet (0)
    Drawing / Dimensional Drawing / 3D (0)
    Exploded View / Spare Parts (0)
    Material Safety Data Sheet (0)
    Operating Instructions (0)
    Others (0)
    Press Release (0)
    Publication / Article (0)
    Software (0)
    Wiring Diagram (0)

    Selected filters:

    Matching downloads

    Sort by Document type
    Load more matches ...
    No more matches available!

    Unfortunately, we did not find an appropriate match.

    All words written correctly?
    Search again with fewer or different search terms?

    Please try again later

    Service Unavailable

    The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.

    Overview

    Reliable protection against biofilm and scaling through real-time monitoring

    DULCOTEST SurfaceGuard is an innovative measurement system for real-time monitoring of deposits on process surfaces. The measurement system consists of a sensor and a transmitter that allows the sensor to be configured.

    The innovative use of two sensors with differently configured surface temperatures enables a precise distinction between biofilms and inorganic deposits. This paves the way for targeted, automated, and needs-based measures such as the efficient dosing of biocides or antiscalants—for optimal process control and sustainable, low-chemical operation.

    By emulating rheological and thermodynamic surface properties, DULCOTEST SurfaceGuard enables precise film thickness measurement of a wide variety of deposits across diverse industrial applications. This ensures representative monitoring of process surfaces—for maximum safety and efficiency.

    Thanks to permanent factory calibration When a metering pump has been installed, the capacity in litres per hour has to be determined under ... more in the glossary, the system remains precise for a long time and requires minimal maintenance. This significantly extends maintenance intervals and noticeably reduces operating costs. Continuous measurement enables seamless monitoring of process efficiency—such as heat transfer in heat exchangers—allowing performance losses to be detected early and their effects minimized.

    Your benefits

    • Reduces energy costs by ensuring the efficiency of industrial systems
    • Enhances process reliability through reliable real-time measurement of biofilms and scaling in the micrometer range
    • Enables targeted and effective measures because biofilm and inorganic deposits are clearly distinguished
    • Provides representative measured values by emulating the process surfaces to be monitored, enabling optimal control of water treatment processes
    • Identifies process changes early, before they negatively impact performance or hygiene
    • Reduces maintenance effort and downtime, as no time-consuming recalibration is required

    Application

    Technical Data

    Downloads

    Contact us

    »Please send us your request! We will contact you shortly.«

    +49 6221 842 0  Send request   

    Matching Products

    • The DULCOMETER diaLog C sets new standards in measuring and control technology. Whether as a transmitter or 2-side controller (PID) with one channel - it is ideal for use in industrial water treatment. Thanks to its intuitive operation and digital networking, it is smartly integrated into your processes.

      more